Differences

This shows you the differences between two versions of the page.

--- ycsserver:dr2x:dr2x_configuration [2021/03/01 23:27] – [Information to the YCS server sysop] dg9ffm
+++ ycsserver:dr2x:dr2x_configuration [2024/10/12 18:53] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ===== Recommended configuration of the DR-2X repeater =====
-After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, transmission power, Callsign and more ...) it can now be connected to a ycs server. The following article describes a recommended configuration for the connection.\\
+After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, transmission power, Callsign and more ...) it can now be connected to a ycs server. The following article describes a recommended configuration for the ycs-server connection.\\
 \\
 \\
@@ Line 17: / Line 17: @@
   * Use "Write to Device..." to write configuration to the repeater
-  * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, if you are using a router, make sure that the port is “open” for passing UDP traffic.//
+  * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, if you are using a router, make sure that the port is “open” for passing UDP traffic inbound and outbound.//
   * On “Destination Repeater's Information” screen, click the button "001". The “Destination Repeater Setting” screen appears.
@@ Line 24: / Line 24: @@
   * Enter the IP address of the desired YCS server
+    *  //for example://
+      * //using Internet: **185.228.139.209** = YCS262 (DE C4FM Germany)//
+      * //using Hamnet: **44.148.237.4** = YCS262 (DE C4FM Germany)//
   * Use "Write to Device..." to write configuration to the repeater
@@ Line 29: / Line 34: @@
 ==== DG-ID configuration of the DR-2X ====
+// => Please follow the instructions carefully so that correct operation is possible with the correct configuration.// \\
+\\
 The next step is to configure the repeater's own DG-ID (01) and the desired DG-ID's to be connected to the YCS server.\\
@@ Line 49: / Line 56: @@
 {{:ycsserver:dr2x:dr2x_local-rpt.jpg?400|}}
-  * Tap on the "DG-ID" field and set "01" with the help of the arrow keys. This is the repeater's own DG-ID (//default "01" on ycs-server//)
+  * Tap on the [DG-ID] field and set "01" with the help of the arrow keys. This is the repeater's own DG-ID (//default "01" on ycs-server//)
-  * Tap on the "Down Link" field and activate "OWN".
+  * Tap on the [Down Link] field and activate "OWN".
-  * Tap twice on the "Name" field and configure repeaters callsign.
+  * Tap twice on the [Name] field and configure repeaters callsign.
-  * Tap "BACK" to go back to DG-ID List screen
+  * Tap [BACK] to go back to DG-ID List screen
 {{:ycsserver:dr2x:dr2x_dgid_mode.jpg?400|}}
+  * Tap on the [RPT Group DG-ID] field
+  * Tap [EDIT] and and write **00** in the field
+  * Tap [BACK] twice to go back to DG-ID List screen
 \\
 In the next step, the DG-IDs are configured which should be connected to the ycs server. It is possible to configure all DG-ID (02-99).\\
@@ Line 126: / Line 138: @@
   * RX-Frequency in Hz //(e.g. 431962500)//
   * TX-Frequency in Hz //(e.g. 439562500)//
-  *
+\\
+\\
+All DG-IDs (Group DG-ID) configured in the DR-2X repeater are now statically (fixed) booked on the YCS server. Especially with many configured DG-IDs, there is a desire to activate some only when required (on demand).\\
+The YCS server sysop has the option to configure all DG-IDs of the DR-2X connection on demand and also to activate your preferred DG-IDs statically if desired.
+Please tell him which DG-IDs you would like to have static (fixed) activated.\\
+\\
+With this function it is possible to configure all DG-ID (02-99) in the DR-2X that they work with the YCS server. On the DR-2X only the traffic of the statically (fixed) activated DG-IDs can be heard.
+All other DG-IDs can be activated by the user on demand by simply sending in the corresponding DG-ID. This DG-ID is then automatically booked dynamically on the YCS server for 10 minutes. This DG-ID deactivates itself automatically after 10 minutes of non-use, or can also be deactivated prematurely by the user by briefly sending it in DG-ID 90.